The BMW of 3 series Е46
+ Cars BMW 3 (Е46)
+ Current leaving and service
+ The engine
- Systems of cooling, heating
+ System of cooling of the engine
- Heater and the conditioner of air of salon
Removal and installation of the block of management of a heater/conditioner
Removal and installation of the fan of a heater
Replacement of additional resistors of the fan of a heater
Removal and installation air дефлекторов
+ Power supply systems, injection and release
+ Engine electric equipment
+ Manual transmission and transmission a line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes
|
Removal and installation of the fan of a heater
The conditioner
|
|
|
1 Remove air collector a box in an impellent compartment, address to Section Removal and installation of a box of an air inlet.
|
2 Turn away bolts of fastening and remove shut-off a wall of a heater-1 from a wall of an impellent compartment-2, a few having rejected it upward. |
|
3 Remove заслонки fresh air-1 at the left and on the right for what reject the lever-2 upwards. |
|
4 Disconnect clips-1, turn out screws-2 and uncover-3 electric motors of the fan. |
|
5 Turn out screws (arrows on an illustration) and uncover the fan. |
|
6 Rasstykujte a socket-1. |
7 Open bracket-2 and cast away it upward.
8 Models 320i, 323i, 328i: Remove the top cover of the engine, address to Section Spark plugs.
9 Disconnect and take out the electric motor of the fan-3 with impeller forward. Thus the electric motor behind raise a little. |
|
|
|
|
0 Insert the fan electric motor. Thus watch that the lath of a back cover was fixed in a back window of the engine.
11 Lower скобы fastenings and fix.
12 Join a socket on the engine.
13 Fix the top cover five bolts.
14 Insert a cover of the electric motor of the fan and fix it from above. Press from below two скобы.
|
15 Connect заслонки fresh air at the left and on the right and fix them for what displace the lever downwards. |
|
16 Connect shut-off a wall of a heater-1 two holders-2 below in a wall of an impellent compartment. Insert a cover both pins-3 into apertures-4 walls of a compartment and fix two screws-5. On an accompanying illustration the left half of cover is shown only. |
17 Establish air collector a box in an impellent compartment, address to Section Removal and installation of a box of an air inlet.
18 Models 320i, 323i, 328i: Establish the top covers of the engine, address to Section Spark plugs. |
|
Heater without the conditioner
|
|
|
19 Remove air collector a box in an impellent compartment, address to Section Removal and installation of a box of an air inlet.
|
20 Remove shut-off a heater wall. |
21 Turn away four bolts of fastening крыльчатки the fan and remove it.
22 Turn away a bolt of fastening of a cover of the electric motor of the fan and remove it.
23 Rasstykujte a socket.
24 Open bracket fastenings of the electric motor and cast away upwards.
25 Models 320i, 323i, 328i: Remove the top covers of the engine, address to Section Spark plugs.
26 Take away forward the electric motor with impeller and take out. Thus raise the electric motor back a little. |
|
|
|
|
27 Establish the electric motor. Thus watch that the lath of a back cover was fixed in a back window of the engine.
28 Cast away downwards bracket and fix it.
29 Join an electric motor socket.
30 Establish a cover of the electric motor and fix a bolt.
31 Establish a cover of a wheel of the fan and fix four screws.
|
32 Establish shut-off a heater wall. |
33 Establish air collector a box in an impellent compartment, address to Section Removal and installation of a box of an air inlet.
34 320i, 323i, 328i: Establish the top covers of the engine. |
|
|
|