|
|
BMW 3 series E46Since 1998 of releaseRepair and car operation |
|
|
The BMW of 3 series Е46 + Cars BMW 3 (Е46) - Current leaving and service Introduction Current leaving The general information on adjustment Check of levels of liquids Check of a condition of tyres and pressure in them. A designation of tyres and disks of wheels Replacement of impellent oil and the oil filter Replacement of a filtering element of the air filter Checks of brake system Replacement of an element of the filter of air of salon Condition check приводных ridge belts Check of a condition and replacement of hoses of an impellent compartment Check of functioning of system of cooling and frost resistance of a cooling liquid Check of a condition of system of release of the fulfilled gases Check of level of oil in a manual box of a gear change Check of a condition of components of a suspension bracket and steering Check of a condition of protective covers of power shafts Check of level of a liquid of system of hydrostrengthening of a wheel Visual check of a body and its bottom Check of seat belts Rotation and replacement of wheels Condition check, replacement of brushes and adjustment of a corner of screen wipers Check of a condition of the battery, care it and gymnastics Replacement of a brake liquid Check and replacement of spark plugs Check of fuel system, replacement of the fuel filter. Operation of diesel model in the conditions of winter Greasing of loops and locks of doors Replacement of a battery of a key of remote control + The engine + Systems of cooling, heating + Power supply systems, injection and release + Engine electric equipment + Manual transmission and transmission a line + Automatic transmission + Coupling and power shafts + Brake system + Suspension bracket and steering + Body + Onboard electric equipment + Electric equipment schemes |
Condition check, replacement of brushes and adjustment of a corner of screen wipers 1 On brushes of screen wipers the road film in due course collects, reducing efficiency of their work, therefore brushes should be washed out regularly in a soft cleaning solution.Check of a condition of brushes and starting position of the lever of a screen wiper 2 Assemblages of screen wipers with brushes should look round regularly. If survey has revealed presence of hardenings or cracks on rubber of brushes, replace brushes. If at survey it is not revealed anything unusual, wet a windscreen, include screen wipers, allow to them to work a little, and switch off them. A non-uniform trace from brushes on glass or strips on pure glass specify that it is necessary to replace brushes. 3 If brushes insufficiently well clear a windscreen following reasons are possible: At passage by the car of an automatic sink on a windscreen wax particles have got. These particles can be removed at addition in a liquid стеклоомывателя a washing-up liquid possessing property to dissolve wax. Filling of the tank for a liquid means for cleaning of glasses with воскорастворяющими properties can essentially improve action of screen wipers. Zhirorastvorjajushchie cleaners not in a condition completely to clear glass. At damage of brushes, it is necessary to replace them. The corner of installation of levers of screen wipers does not correspond to the necessary. During work of the mechanism of screen wipers there can be an easing of fixing nuts, therefore they should be checked and necessarily to tighten each time at check of brushes. Check 4 Switch on and off screen wipers, thus they will be established in a starting position. 5 Check up distance between an elastic band of a brush of a screen wiper and the basis of glass which 20 mm on a windscreen should be. Check and adjustment of a corner of the lever of a screen wiper
Check 6 Establish screen wiper levers in a starting position. For this purpose moisten a windscreen with water. Include for short time a screen wiper and stop its switch. 7 Remove a brush.
9 Cautiously take away back the lever. Tool HAZET should adjoin to glass in three points. 10 Check up an installation corner on a scale of the tool and compare to demanded value. Demanded value:-3 ° ± 2 °. Adjustment
12 Check up an installation corner again and if necessary modify it so that on a scale there was a demanded value. 13 After that remove the tool, once again establish and fix it. Again check up an installation corner, if necessary modify. |
|